MIG welder SOLARIS MULTIMIG-227 (160-240 V~, 10-220 A, MIG/SPOT/FLUX/MMA/TIG, polarity change, 2T/4T, euro connector, 3 m torch)

Vendor code: MULTIMIG-227

Characteristics

Wire diameter used: 0.6–1.0 mm

Gas fitting: 9 mm

Input voltage: 160–240 V~

Network type: 1 phase

Open circuit voltage: 67 V

Rated input current: 16 A

Maximum input current: 28 A

Power factor: COS 0.87

Insulation class: H

Protection rating: IP21S

Weight (without accessories): 14.3 kg

Network plug included: no

Mains Frequency: 50/60 Hz

at 40°C: 35% (EN 60974–1)

at At 20°C: 60%

Rated power consumption at maximum current: 3.5 kW

MMA Welding Current: 10–200 A

Efficiency: 0.91

Overall dimensions (L x W x H): 480 x 200 x 380 mm

Recommended generator Power: 6.5 kV A

TIG Welding Current: 10–200 A

Electrode diameter: 1.6–4.0 mm

MIG Welding Current: 20–220 A

TIG electrode diameter: 0.5–2.4 mm

Warranty period: 24 months

Description:

Advantages:

■ 3m burner with EURO connector

■ 3 in 1 (MIG / MMA / TIG lift DC)

■ Microprocessor control

■ The device runs on 6 IGBT transistors, which makes it a more reliable solution

■ High operating time of the device 60% at 20 °C

■ Installed coil size up to 5 kg / 200 mm

■ Wire threading assistance system when there is no welding for 3 seconds, the device increases the wire feed speed to speed up the process of threading a new spool

■ Metal wire feeder

■ Possibility of changing polarity for welding with wire without gas (FLUX)

■ Stable operation in networks with reduced voltage (from 160 V)

■ 2T/4T mode (for MIG)

■ SPOT welding mode (spot welding with duration from 0.1 to 10 seconds)

■ Arc force adjustment (MMA)

■ HotStart, AntiStick (MMA) functions

■ Power cable 2 m (without power plug)

■ Noise filter to protect other devices from interference.

Description:

Note! The device is supplied without a plug. In case of operation at maximum currents, the device must be equipped with a 32A 230V single-phase power plug (not included). Note! Some accessories (torch, ground terminal) are located inside the wire feed compartment. Multifunctional inverter welding machine that allows you to weld in five modes: - mode of semi-automatic welding in a protective gas environment MIGMAG; - SPOT welding mode (spot welding with duration from 0.3 to 30 seconds); - mode of semi-automatic welding with flux-cored wire without the use of FLUX shielding gases; - mode of manual arc welding with coated MMA electrodes; - argon-arc welding mode with direct current LIFT DC TIG (valve-type torch must be purchased separately). The device is equipped with a EURO connector, a 3 meter MIG torch and the ability to change polarity for welding with wire without gas (FLUX). The SPOT spot welding mode is ideal for welding thin sheet metal (for example, car bodies). It is necessary to adjust the welding time of one point, and after that all spot seams will be welded equally well and with high quality. when using a 15AK type burner

Equipment:

+ Inverter semi-automatic

+ Welding torch 3 meters

+ Electrode holder with 2 meter cable

+ Ground terminal with 2 meter cable

+ Gas hose 2 meters

+ Feed roller for wire 0.6-0.8 mm (installed in the wire feed mechanism)